The IKE protocol uses encryption that can be accelerated. But since IKE only generates a few packets per hour per IPsec connection, compared to the thousands or millions of IPsec packets per hour, this is not worth any extra overhead to talk to some kind of hardware driver. The exception is on-CPU special instructions, such as AESNI or the VIA Padlock instructions. Acceleration of these happen via the NSS crypto library and does not require specific libreswan support.
Obsoleted IPsec accelerations
Libreswan (for now) still supports its own older KLIPS IPsec stack that comes with its own OCD based acceleration. It is not recommended to use KLIPS anymore. KLIPS has no support for AES_GCM and its OCF acceleration does not support modern NICs that can do 1gbps to 400Gbps.
Similarly, the pcrypt module provides additional parallelism but it predates some modern Linux kernel network stack and crypto stack implementatios and should not be used anymore.
Information about these two older hardware accelerations are left at the end of this document.
IPsec (ESP) acceleration
libreswan as of version 3.23 supports the new cryptographic hardware offload as implemented by Linux 4.11 and up using the native (XFRM) IPsec stack.
Libreswan autodetects supports for any hardware supporting this crypto offload API. However, it might require that some hardware driver modules are loaded before libreswan is started. The "ipsec _stackmanager start" command, which is typically run before the pluto IKE daemon is started, attempts loads all known hardware modules. If you know of any module not loaded, please contact the libreswan developers. These hardware modules include CPU specific ones (eg AESNI or VIA Padlock) as well as NIC card modules. Although usually the IPsec offload support is integrated into the NIC card driver and will not require specific hardware crypto modules to be loaded.
The crypto API comes with defaults that are suitable for generic machines. If your machine is a dedicated IPsec server, you might want to change some default parameters. This is especially important for the crypto API queue length parameter. This was hardcoded to 100 for most kernels and changed to 1000 in 2017 but recent kernels allow you to increase that value by (re)loading the crypd module:
modprobe cryptd cryptd_max_cpu_qlen=2048
Even when using regular 1gbps NIC cards with only AESNI acceleration, the value of 100 is not enough and will cause your machine to idle instead of fully using its CPUs for IPsec.
libreswan auto-detects PCI card nic offload support (enabled since 3.23 with the option nic-offload=auto). This option can be set to "yes" (or "no") to override the default auto-detection. Note that when failing to add IPsec SA's into the kernel are automatically retried without offload. This can happen for a number of reasons. The selected algorithm (eg 3DES) has no hardware offload support. Or the hardware could have reached the maximum number of IPsec SA's it can support for offloading.
There are two typical deployment scenario's that require hardware acceleration.
site to site VPNs
These deployments involves only one or very few IPsec connections transporting anywhre from 1 to 400 Gbps. Especially on multi-CPU machines, this can lead to unused resources as an IPsec SA is typically tied to one CPU's resources. A workaround can be to split the IPsec connection into artificial smaller IPsec connections. Libreswan will soon have populate-from-packet (PFP) support to make this easy.
Remote Access VPNs
These are deployments with thousands of IPsec connections and clients are continuously being added and removed. Some NIC cards are limited in their offload capacity, so not all connections might be accelerated. Since there are still a number of bottlenecks in the kernel for this scenario, it is important to remove unused IPsec SA's from the kernel. Typically, that means using DPD/liveness to kill of inactive clients that have vanished, and cleaning out replaced IPsec SA's more quickly. When possible, use libreswan 3.24 as it no longer keeps replaced IPsec SA's around for 20 minutes.
The below list is hardware that The Libreswan Project knows about that supports to new Linux 4.11 crypto hardware offload API. If you know of others, or are a vendor that would like to be listed, please contact the libreswan developers.
- Mellanox Innova (mlx5) - http://www.mellanox.com/page/products_dyn?product_family=249&mtag=programmable_network_adapters
- Chelsio (cxgb4) - https://www.chelsio.com/crypto-solution/
- Intel (ixgbe / ixgbevf) - Intel 540 and 82599 Limited to 1024 sessions maximum and 128 IP address maximum - https://blogs.oracle.com/linux/tips-and-tricks-for-ipsec-on-intel-10-gbe-nics-v2
- Intel QuickAssist (QAT) - http://dpdk.org/doc/guides/cryptodevs/qat.html
- CAAM / NXP i.MX6 SoC - http://events17.linuxfoundation.org/sites/events/files/slides/2017-02%20-%20ELC%20-%20Hudson%20-%20Linux%20Cryptographic%20Acceleration%20on%20an%20MX6.pdf
- Broadcom SPU driver
- Cavium Nitrox / Octeon-tx CPT Engine
Obsoleted OCF Hardware Crypto Acceleration (KLIPS and XFRM)
In general, cryptographic acceleration is mostly useful for embedded and low power systems. High end systems tend to have a CPU that is fast enough, especially when using AES_GCM on a multi-CPU system with AESNI support. Although if you are trying to get 5gbps or higher throughput, you might want to use a dedicated crypto acceleration card on top of the CPUs (such as the Intel QuickAssist PCIe)
There are a few methods for crypto hardware acceleration. The most complete one is the Open Cryptographic Framework ("OCF"), a port of the OpenBSD code. A newer more native implementation is the CryptoAPI async interface. The latter implementation is still extremely limited. It does not have as many drivers as OCF. But it just works without needing to do anything on the system. There is also the pcrypt kernel module that uses multiple CPUs for parallel processing.
Libreswan supports OCF using the KLIPS IPsec stack and using the XFRM/NETKEY stack. The latter needs the OCF cryptosoft.ko kernel module.
On an IPsec gateway, almost all the encryption is done inside the kernel when doing the actual IPsec encryption and decryption. The IKE negotiations also use encryption, but since this only involves a few packets per hour, there isn't really much point in accelerating these. While some acceleration might be available to the userland, support for that would be automatically enabled in the NSS crypto library when supported. The overhead of sending IKE packets to the kernel accelerator for encryption/decryption is not worth it and might actually slow things down.
OCF: Kernel and Userland crypto acceleration
OCF provides kernel crypto acceleration for IPsec (ESP and AH) as well as userland crypto acceleration via the /dev/crypto interface. Libreswan has removed OCF support for IKE, as the overhead is simply not worth the efforts even on embedded systems. It also required OCF patches to the TTY subsystem and thus an entire kernel recompile. If only kernel level acceleration is needed, OCF can be build as a kernel module without requiring a recompile of the entire base kernel. The userland /dev/crypto interface can however be used by other userland based applications that use openssl. For example, if the system also supports OpenVPN, it will be very useful to have OCF userland support in openssl.
Supported hardware via OCF
- Safenet SafeXcel 1741 and SafeXcel 1142
- Intel IXP465, IXP425 and IXP422
- Freescale SEC (Talitos) (this is also the bsec driver used on Linksys WRT54g, AsusWL500g)
- PA Semi PWRficient DMA Crypto Engine
- Intel EP80579 (Intel QuickAssist enabled EP80579 Integrated Processor Product Line)
- PMC Sierra MSP-8520 (requires vendor-supplied source code for OCF)
- Cavium Octeon (requires vendor-supplied source code for OCF)
- Hifn 7951 and Hifn 7956
Supported hardware via cryptosoft.ko kernel module
The OCF subsystem can interface with the XFRM Linux kernel crypto acceleration system. It does so via the OCF cryptosoft kernel module.
- VIA Padlock (via cryptosoft)
- AMD Geode LX (via cryptosoft)
- SMP (multi-core) support (via cryptosoft)
Supported algorithms and ciphers with libreswan
- 3DES and 1DES
Note that SHA2 support for OCF with KLIPS is missing from the list!
Note that not all hardware implementations support all these algorithms and ciphers. Libreswan no longer supports 1DES because it is too insecure.
The Linux NETKEY/XFRM native IPsec stack does not load balance a single IPsec SA over multiple CPU cores. Using the OCF cryptosoft driver, a single IPsec SA can be offloaded over multiple CPU's
Building libreswan with OCF support
Some OCF kernel builds are made available at libreswan.org, usually in the form of source and binary .deb or .rpm packages. the kernel packages provided support both kernel and userland OCF acceleration. You will also find patched openssl packages there which can be used in combination with openvpn to support hardware acceleration in userland.
Building kernel only OCF support as a module for running kernel
tar zxf ocf-linux-20120127.tar.gz cd ocf-linux-20120127/ocf make ocf_modules sudo make ocf_install OCF_DIR=`pwd`
You can test the OCF acceleration using a special benchmark module called ofc-bench. This is a kernel module that performs benchmarking when modprobe'd into the kernel. It will also fake an error to unload itself
modprobe ocf modprobe cryptosoft modprobe ocf-bench dmesg | tail -5
You should see something along the lines of:
[ 583.128741] OCF: 45133 requests of 1488 bytes in 251 jiffies (535.122 Mbps)
Building KLIPS with OCF support
To build libreswan KLIPS with OCF support, instead of using make module, use:
make KBUILD_EXTRA_SYMBOLS=$OCF_DIR/Module.symvers \ MODULE_DEF_INCLUDE=`pwd`/packaging/ocf/config-all.hmodules \ MODULE_DEFCONFIG=`pwd`/packaging/ocf/defconfig \ module sudo make KBUILD_EXTRA_SYMBOLS=$OCF_DIR/Module.symvers \ MODULE_DEF_INCLUDE=`pwd`/packaging/ocf/config-all.hmodules \ MODULE_DEFCONFIG=`pwd`/packaging/ocf/defconfig \ minstall
Building userland OCF support for IKE
OCF support for IKE has been removed, as it is faster to use the CPU instruction support via the userland CPU instructions these days. Support for those instructions come in via the NSS library that libreswan uses. It has the advantage of not requiring a kernel patch.
Generate the kernel patches and apply the appropriate one
If you want OCF random support, you cannot just build the ocf as module, you also need to patch the kernel.
cd ocf make patch
This will provide four files:
Depending on your kernel, pick the appropriate patch and apply it to your kernel, for example for a 3.1 kernel use:
cd linux-3.1 patch -p1 < linux-3.1-ocf.patch
|For Linux 2.4 kernels on non-x86, you might need to issue: cp linux-2.X.x/include/asm-i386/kmap_types.h linux-2.X.x/include/asm-YYY|
To compile userland applications with OCF support, the cryptodev.h file needs to be installed on the system, for example in /usr/include/crypto/cryptodev.h
The OCF source code comes with openssl patches as well, please see the OCF source for further instructions.
How to load the OCF modules into the kernel
Libreswan comes with the _stackmanager script that loads all kernel modules and sets various parameters. These include all the native CryptoAPI acceleration modules. It does not auto-detect OCF support on disk, so before starting _stackmanager, ensure that the system has loaded the OCF core kernel module:
Libreswan will detect OCF support and load the userland (cryptodev) and software driver (cryptosoft)
To load any of the OCF hardware drivers, ensure you load the appropriate hardware driver, eg one of:
modprobe safe modprobe hifn7751 modprobe ixp4xx ...
|You might wish to change _stackmanager to not load the cryptosoft module if you have native OCF hardware driver support. In some cases the software driver has accidentally gained preference over a hardware driver|
To enable debugging (which will ruin your acceleration gains!) you can issue some of the following commands based on your hardware/software:
echo 1 > /sys/module/ocf/parameters/crypto_debug echo 1 > /sys/module/cryptodev/parameters/cryptodev_debug echo 1 > /sys/module/cryptosoft/parameters/swcr_debug echo 1 > /sys/module/hifn7751/parameters/hifn_debug echo 1 > /sys/module/safe/parameters/safe_debug echo 1 > /sys/module/ixp4xx/parameters/ixp_debug
The ocf-bench driver accepts the following parameters:
- request_q_len - Maximum number of outstanding requests to OCF - request_num - run for at least this many requests - request_size - size of each request (multiple of 16 bytes recommended) - request_batch - enable OCF request batching - request_cbimm - enable OCF immediate callback on completion
An example benchmark use:
modprobe ocf-bench request_size=1024 request_cbimm=0 dmesg |tail -5
OCF KLIPS tuning
The following parameters are managed by _stackmanager but can be changed to suit your specific need based on the hardware capabilities of your platform:
Additional parameters that can be tuned manually:
The OCF layer will call back on completion immediately rather than calling back from a work queue (softirq) context. Your callbacks need to be very careful and re-entrant safe to use this mode. KLIPS is typically safe to use in this mode.
Instruct OCF to batch requests if possible. Typically this should be enabled.
The (obsoleted) pcrypt kernel module
The pcrypt and tcrypt kernel module allows the Linux kernel CryptoAPI to spread the crypto load of single IPsec SA's over multiple CPU's. If your VPN server has many hunderds of IPsec connections, these will already be spread out over the CPU's and pcrypt does not gain you much. However, if you have only one or a few IPsec tunnels that run at a high capacity, the pcrypt module might help you better use all your available CPU power. Also, if you are looking at increasing the throughput, it is very important to pick an ESP algorithm that is fast. Currently, AES_GCM outperforms everything (including esp=null-md5 !!) so that should be the algorithm used when trying to use pcrypt.
|The pcrypt module is VERY UNSTABLE. Please be careful. If you have stability tips, please let us know at firstname.lastname@example.org|
The documentation of the pcrypt / tcrypt module is very limited. The pcrypt module has to be enabled per algorithm:
modprobe pcrypt modprobe tcrypt alg="pcrypt(rfc4106(gcm(aes)))" type=3 # optionally accelerate aes-sha1 and aes-sha2 modprobe tcrypt alg="pcrypt(authenc(hmac(sha1),cbc(aes)))" type=3 modprobe tcrypt alg="pcrypt(authenc(hmac(sha256),cbc(aes)))" type=3
Note that it has been reported that a system may crash if these commands are activated before any IPsec tunnel has been established. Similarly, we have reports that these commands must be run before starting any tunnels or otherwise it crashes. And we have had reports that after running the modprobe commands, the IPsec tunnel should be re-established to activate the acceleration.
Using multiple CPU's can cause packets to become encrypted out-of-order. It is important to either increase the replay-window to a value of 64 or 128, or to disable replay protection by setting replay-window to 0.
There is a tool called crconf that is supposed to make this easier, but it seems to not be working for those who have tried to use it.