Difference between revisions of "VPN server for remote clients using IKEv1 with L2TP"
|Line 180:||Line 180:|
And your /etc/ppp
And your /etc/pppoptions.server would contain:
Revision as of 12:58, 19 October 2021
Using IPsec/L2TP is a common deployment. Note that it is a dated solution that should be avoided when possible. Specifically, there are issues with multiple Transport Mode IPsec connections and NAT. Additionally, L2TP clients tend to be PSK based using Aggressive Mode, which is also an unwise choice from a security perspective. There will be two extra layers of packet encapsulation, a PPP layer and an L2TP layer. This can cause MTU issues, so usually the L2TP/IPsec client uses an MTU of 1200 for the ppp device that is created.
|While we document how to run an L2TP/IPsec server, we do not recommend this type of setup.|
L2TP/IPsec based server
If you place your L2TP/IPsec server behind NAT (such as on Amazon AWS) you will need to change Registry settings on Windows to allow it to connect to IPsec servers behind NAT
As this is the most widely (yet least secure) supported IPsec configuration, almost every enduser device that supports IPsec, supports this setup.
- All Apple iphones, ipads
- Mac OSX
- Linux with commandline
- Microsoft Windows
The server has three components to configure: libreswan for IPsec, xl2tpd for L2TP and pppd for PPP.
IPsec server configuration
We are going to hand out IP address from the range 100.64.0.10/24 via PPP. So we need to exclude those addresses from being used by the remote endpoints as pre-NAT address. It is important to keep your address pool small and not a commonly used IP range like 10.0.0.0/24 to avoid collisions with pre-NAT IP addresses. We use something from the range 100.64.0.0/10 which is reserved for Carrier-grade NAT and should therefore never be visible on the internet, and unlike the traditional RFC-1918 address space is not commonly in use for local networks.
config setup # needed when using PSK only. Not needed for X.509 based servers uniqueids=no virtual-private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12,%v4:188.8.131.52/8,%v4:100.64.0.0/10,%v4:!100.64.0.0/24 conn ikev1 authby=secret pfs=no auto=add rekey=no left=%defaultroute right=%any ikev2=never type=transport leftprotoport=17/1701 rightprotoport=17/%any dpddelay=15 dpdtimeout=30 dpdaction=clear conn ikev1-nat also=ikev1 rightsubnet=vhost:%priv
And of course your PreSharedKey (PSK) in /etc/ipsec.secrets
: PSK "strongrandomstring"
For the L2TP server, we use xl2tpd.
[global] listen-addr = YourPublicIP ipsec saref = no force userspace = no ; debug tunnel = yes [lns default] ip range = 100.64.0.100-100.64.0.200 local ip = 100.64.0.1 require chap = yes refuse pap = yes require authentication = yes name = LinuxVPNserver ppp debug = yes pppoptfile = /etc/ppp/options.xl2tpd length bit = yes
Some xl2tpd versions are buggy when you leave out the ipsec saref setting even if you want it to be 'no'. The force userspace option is required to allow the kernel to decapsulate L2TP data packets so only L2TP control packets make it to userland's xl2tpd. This significantly increases performance.
The IP address from the pool is handed over to PPP.
PPP server configuration
This is done via the above pppoptfile, in our case /etc/ppp/options.xl2tpd
ipcp-accept-local ipcp-accept-remote # use an internal server for DNS if you need to reach local-only zones or if # you want DNS to be encrypted through the tunnel. ms-dns 100.64.0.1 # ms-dns 184.108.40.206 # ms-dns noccp auth crtscts idle 1800 # when having MTU issues, can be decreased to about 1200 mtu 1410 mru 1410 nodefaultroute debug lock proxyarp connect-delay 5000
In this case, we are using a simple ppp configuration with usernames and passwords specified in /etc/ppp/chap-secrets. You can hand out static IPs (that should not be taken from the pool!) or hand them out from the L2TP pool.
# /etc/ppp/chap-secrets # Secrets for authentication using CHAP # client server secret IP addresses user1 * "password1" 10.10.64.2 user2 * "password2" 10.10.64.3 user10 * "secret10" * user11 * "geheim" * #
If you want to use a radius plugin instead, change /etc/ppp/options.xl2tpd to include:
require-pap plugin radius.so plugin radattr.so radius-config-file /etc/radiusclient-ng/radiusclient.conf
L2TP/IPsec client configuration
Configuring most clients such as mobile phones is pretty simple. The information you need to configure on the client is:
- The remote server DNS name or IP address - The L2TP username and password - The PreSharedKey, sometimes called "Secret"
The ipsec.secrets would be the same as the server secrets file. The ipsec.conf entry would be almost identical:
config setup # needed when using PSK only. Not needed for X.509 based servers conn ikev1 authby=secret pfs=no auto=add rekey=no left=%defaultroute # DNS name or IP of the VPN server you want to connect to right=YourVPNServerIP type=transport leftprotoport=17/1701 rightprotoport=17/1701 dpddelay=30 dpdtimeout=70 dpdaction=clear
Your /etc/xl2tpd/xl2tpd.conf file would be:
[global] ; no need for listen-addr [lac serer] ; DNS name or VPN server IP lns = VPNServerIP ppp debug = yes pppoptfile = /etc/ppp/options.server
And your /etc/ppp/options.server would contain:
ipcp-accept-local ipcp-accept-remote refuse-eap require-mschap-v2 noccp noauth idle 1800 mtu 1200 mru 1200 defaultroute noipdefault usepeerdns debug lock connect-delay 5000 name YourName password YourPassword