XFRM Interface Development Notes
Development notes for XFRMi
libreswan/pluto design choices
- allow names ipsec0, ipsec1 ... ipsecx.
- Should we allow names other than ipsecXX ?
- initial thought is keep "xfrm interface id" and "xfrm output mark" consistent.
- interface creation is inside pluto.
- create bugzilla entry for Fedora/CentOS kernels? Fedora 28 do not enable
XFRM INTERFACE
Commit cover letter from Steffen 20180612, Merged in 4.19:
https://patchwork.ozlabs.org/cover/928175/ Steffen Klassert June 12, 2018, 7:56 a.m. This patchset introduces new virtual xfrm interfaces. The design of virtual xfrm interfaces interfaces was discussed at the Linux IPsec workshop 2018. This patchset implements these interfaces as the IPsec userspace and kernel developers agreed. The purpose of these interfaces is to overcome the design limitations that the existing VTI devices have. The main limitations that we see with the current VTI are the following: - VTI interfaces are L3 tunnels with configurable endpoints. For xfrm, the tunnel endpoint are already determined by the SA. So the VTI tunnel endpoints must be either the same as on the SA or wildcards. In case VTI tunnel endpoints are same as on the SA, we get a one to one correlation between the SA and the tunnel. So each SA needs its own tunnel interface. On the other hand, we can have only one VTI tunnel with wildcard src/dst tunnel endpoints in the system because the lookup is based on the tunnel endpoints. The existing tunnel lookup won't work with multiple tunnels with wildcard tunnel endpoints. Some usecases require more than on VTI tunnel of this type, for example if somebody has multiple namespaces and every namespace requires such a VTI. - VTI needs separate interfaces for IPv4 and IPv6 tunnels. So when routing to a VTI, we have to know to which address family this traffic class is going to be encapsulated. This is a lmitation because it makes routing more complex and it is not always possible to know what happens behind the VTI, e.g. when the VTI is move to some namespace. - VTI works just with tunnel mode SAs. We need generic interfaces that ensures transfomation, regardless of the xfrm mode and the encapsulated address family. - VTI is configured with a combination GRE keys and xfrm marks. With this we have to deal with some extra cases in the generic tunnel lookup because the GRE keys on the VTI are actually not GRE keys, the GRE keys were just reused for something else. All extensions to the VTI interfaces would require to add even more complexity to the generic tunnel lookup. To overcome this, we started with the following design goal: - It should be possible to tunnel IPv4 and IPv6 through the same interface. - No limitation on xfrm mode (tunnel, transport and beet). - Should be a generic virtual interface that ensures IPsec transformation, no need to know what happens behind the interface. - Interfaces should be configured with a new key that must match a new policy/SA lookup key. - The lookup logic should stay in the xfrm codebase, no need to change or extend generic routing and tunnel lookups. - Should be possible to use IPsec hardware offloads of the underlying interface.
Initial xfrmi kernel commits
- Steffen Klassert's at Linux IPsec 2018, Dresden https://workshop.linux-ipsec.org/2018/slides/xfrm_interfaces.pdf
XFRM OUTPUT_MARK (required commits to be pulled to RHEL)
Add mask and rename to XFRMA_SET_MARK, Steffen
Which mark?
Two marks related to xfrm code in Linux kernel. XFRMA_MARK and XFRMA_SET_MARK(aka XFRMA_OUTPUT_MARK). Now on I use XFRM_OUTPUT_MARK mark which as of 4.20 mean XFRM_SET_MARK/XFRM_SET_MARK_MASK
One line difference. XFRM_OUTPUT_MARK mark is for routing a packet after XFRM (ESP out or Clear text in), while XFRMA_MARK could be sees as routing a clear text packet into xfrm code, XFRMA_MARK is a lookup key of SPDB and SADB.
XFRMA_MARK is used inside xfrm code (clear text packet out only) code. One could say both marks are used for routing a packet. However XFRM_SET_MARK it is used from routing say outgoing clear text packet. While XFRM_SET_MARK is used for rougint ESP packet on the output side and clear text packet on the input side.
[https://lwn.net/Articles/375829/ Jamal's explination https://lwn.net/Articles/375829/ XFRMA_MARK syntax is mark(u32)/mark(u32). XFRM_OUTPUT_MARK
Fedora support
- F29 commit enabled it. However not in F28
- RHEL bugzilla request??